Router Feed Direction

2 Easy Ways to Remember Router Feed Direction (Quick Tip) KatzMoses

In the majority of cuts, you feed against the rotation of the bit. Don't imagine you can muscle in to dampen kickback manually. The opposite of normal feed direction is called climb cutting. The force is not with you. But this appears to be contrary to everything i read on the internet, which says outside edge routing should be done.

2 Easy Ways to Remember Router Feed Direction (Quick Tip) KatzMoses

But this appears to be contrary to everything i read on the internet, which says outside edge routing should be done in a counterclockwise motion. It tends to bounce erratically or walk out. Used my router table for the first time recently, making some simple cove molding. The back of your hand represents the router, your palm is the base.

Feed Direction, Complicated? Router Forums

The normal feed direction is against the rotation of the bit,which means on the outside edges you would move the router counter clockwise,on the interior move the router clockwise. But this appears to be contrary to everything i read on the internet, which says outside edge routing should be done in a counterclockwise motion. If on the right, you pull.

2 Easy Ways to Remember Router Feed Direction (Quick Tip) KatzMoses

In the majority of cuts, you feed against the rotation of the bit. The back of your hand represents the router, your palm is the base plate, that is to say it is the part that would be touching the wood. So, feed direction reverses also. The force is not with you. The opposite of normal feed direction is called.

direction of feed? Router Forums

If on the right, you pull the router towards you. Used my router table for the first time recently, making some simple cove molding. The router is much more difficult to control in climbing. Feeding with the rotation makes the bit pull the router and this is climb cutting. 2846 views 19 replies 11 participants last post.

Router Feed Direction - The normal feed direction is against the rotation of the bit,which means on the outside edges you would move the router counter clockwise,on the interior move the router clockwise. In the majority of cuts, you feed against the rotation of the bit. So, feed direction reverses also. But this appears to be contrary to everything i read on the internet, which says outside edge routing should be done in a counterclockwise motion. The climb cut method is more suitable for mechanical feed on a shaper. It tends to bounce erratically or walk out.

Sorry to be so wordy. The opposite of normal feed direction is called climb cutting. With the router in its normal position the bit turns clockwise,upside down table mounted it turns counter clockwise. The force is not with you. I have an old craftsman 315.17461 router (from the 1980's!) and the instructions say to move the router in a clockwise direction when routing an outside edge (see attached page).

The Back Of Your Hand Represents The Router, Your Palm Is The Base Plate, That Is To Say It Is The Part That Would Be Touching The Wood.

The router is much more difficult to control in climbing. Going around the outside of a work piece, you go counter clockwise. The opposite of normal feed direction is called climb cutting. If you do it palm up it would be a table mounted router.

On A Router Table, Bits Spin Counterclockwise.

But this appears to be contrary to everything i read on the internet, which says outside edge routing should be done in a counterclockwise motion. In the majority of cuts, you feed against the rotation of the bit. I have an old craftsman 315.17461 router (from the 1980's!) and the instructions say to move the router in a clockwise direction when routing an outside edge (see attached page). So, feed direction reverses also.

2846 Views 19 Replies 11 Participants Last Post.

Used my router table for the first time recently, making some simple cove molding. Sorry to be so wordy. With the router in its normal position the bit turns clockwise,upside down table mounted it turns counter clockwise. Feeding with the rotation makes the bit pull the router and this is climb cutting.

Your Thumb Points At The Work Piece Edge And Your Index Finger Points In The Feed Direction.

This technique causes a bit to pull you in the rotation direction. It tends to bounce erratically or walk out. If on the right, you pull the router towards you. The climb cut method is more suitable for mechanical feed on a shaper.